DO NOT TRY THIS AT HOME : Rotteneggs.com text files and message bases are for INFORMATIONAL PURPOSES ONLY. DO NOT undertake any project based upon any information obtained from this or any other web site.We are not responsible for, nor do we assume any liability for, damages resulting from the use of any information on this site.
(116 votes) Published: May 16, 2005 6:18 p.m. In 16 Favorites Lists Viewed 4403 times
well i asked around school about this egg and on of the biggest pyro said it was "a genious idea" if you guys dont like it so what. i dont have to please anyone.
what you need:
1. a new, unopened can of soda
2. exacto knife
3. smoke bomb ingridents (just look on this site but i think Rambo4104 has the best recipe. [sorry Rambo if i mispelled anything])
4. sturdy match (not from a book, but a box diamond are the best in my opinion)
5. match strike pad (prefferably from a book)
6. small block of wood
7. small circular piece of cardboard
8. small metal screw
what you do:
1. carefully cut the can 2/3 from the bottom and let the pop drain out, might be wise to clean and dry
2.on the bottom part fill it to the top with your recipe of smoke bomb and put the circular piece of cardboard on top of the mixtrue (make sure theres a hole for the fuse in the center and little vent holes for the smoke to seep through) when all that is done you can insert the fuse. try to use a bottle rocket fuse so it sticks straight up, if it is not you can prop it against a toothpick or a popsicle stick.
3. now for the ingnition system of this grenade. first you superglue the match to the bottom of the lid. then to be safe put some masking tape on it. just make sure it is tight.
4. for the block of wood (part 2 of the ingnition system) it has to be small enough to fit in the can and long enough to fit on top of the cardboard. you have to sand the wood so it is on the same angle of the lid when it openes. after that you can glue the strike pad to the block. when you get that you can screw it in to the side of the can where you drink from.
5. for this step you can fit the top part over the bottom so that the wooden ingnition system touches the cardboard right by the fuse. so when it opens the match strikes the pad and the match lines up with the fuse. you might want to make it so that the fuse is taller than the tip of the match because the fire would burn up.
6. for the final part tape it all up with desired tape and when its wrapped up pretty tight, drill some holes in the sides so the smoke can flow out.
to work it pop the lid and listen for hissing of the fuse being lit. once you hear that either throw it or set it on the ground.
Jun 14, 2005 11:47 am - i just thought of this, instead of using a flimsey fuse you can also use a sturdier sparkler. man i wish i would think before i act.
Jun 25, 2005 6:48 pm - thank you alpha. im gonna put different chemicals in the mix to make different color smokes and use them everywhere. im also going to sell them. you guys can too i dont care.
Jul 29, 2005 5:37 pm - or....... you could just buy a bunch of little round smoke bombs and tye the fuses together throw it in a room and if you wanna killem then just wait for the smoke to clear and shoot him/her in the throat with a 22.
Jul 29, 2005 5:39 pm - pussy Stefago, didnt your mommy ever tell you its bad to lie?
Nov 18, 2005 5:34 pm -
Quote:
you could just buy a bunch of little round smoke bombs and tye the fuses together throw it in a room and if you wanna killem then just wait for the smoke to clear and shoot him/her in the throat with a 22.
OR, you could shut the fuck up and make it like he said.....HEY! that works too!
Dec 20, 2005 3:42 pm - sparkler would be good but it takes time to light them..maybe if you made like a sticky blackpowdercompound to put on the tip of it...or just use a sturdy fuse..either way good egg 5*
Mar 25, 2006 4:31 am - yeah mad but get those piks man and the igniotion system needs sum fine tunin(maybe sum more match heads not jus the 1) but othawise cool
Edit Page
Message C-SKI
Add Comment
Add to Favorites
Email to Friend
